Serial # M1000-99-171, Stock Number: 4730
10 HP, 230/460 Volt, 3 Phase (wired for 230 Volt),
24" W x 125" L x 97" T, Weight: 800 lbs
Rated at 4 000 CFM, 12" Inlet, (3) 60" Tall upper filter bags
(3) 72" tall lower plastic collection bags
45 cubic feet storage capacity, Quick-release straps

Serial # 0105027314,Stock Number: 4369
Spindle Arbor Size: 1-1/4",Spindle Travel: 3"
Under Nut: 4-7/8", Table Top Size: 28" x 30"
Motor HP: 5, Electrical: 230/460V(Wired 230)/3PH
Approx. Shipping Weight: 800 Lbs.
Approx. Shipping Dimensions: 48" L x 40" W x 55" H
3-1/2" Dust Collection Shroud

Serial # 871254-1,Stock Number: 4345
Motor Horsepower 7.5, Saw Diameter 16", Saw Hole 1",
Dado* Largest Width on Standard Mandrel 1-9/16"
Dado* Largest Width on 1-3/8", Standard Mandrel 3"
Maximum Depth of Cut (16" Saw) 4-1/2"
Cross Cut Capacity-Guide Fence Regular Position 17-1/2"
Cross Cut Capacity-Guide Fence Rear Position 25"

- 84" x 48" clamping capacity
- 30 degree inclined angle for ease of clamping
- 2-1/4" tall x 5" wide jaws main jaws
- (1) 6" bore x 2" stroke air cylinder provides main pressure
- (2) 4" bore x 2" stroke pneumatic cylinders provide auxiliary side pressure
- Main jaw set-up adjustment by manual hand crank via screw

Serial # 127-7535, Floor Standing
3/4 HP, 208 Volt, 3 Phase

9" Blade, 15" Crosscut Capacity, Good condition, 3/4 HP motor,
Single Phase, 115 Volt, Includes blade

1500mm (4.9') working length, 1100mm (3.6') cutting width
4HP approximately, Single Phase, Scoring unit

25" x 60" Overall table size, 6" X 108" Belt size, 6" X 40" Platen
2 HP 3PH 220 Volt, 3400 FPM Belt speed, Machine weight approximately 400 lbs.
Overall dimensions 66" wide x 20" deep x 45" high

13-Spindle Line Boring Machine 3/4 HP Spindle Drive Motor,
TEFC 60" Back Fence Assembly (1) 13-Vertical Gear Driven Spindle Rows
10mm Bored Collets (7) Right Hand, (6) Left Hand (2) Index Pins
20" X 48" Work Table Surface Wired 1-Phase 120 Volt, 60 Hz.
Manually Actuated Boring Cycle

1/4" to 5/8" collet size 6 adjustable spindle depths
4" spindle travel 29.5" throat depth 30" x 36" non-tilting cast iron table
7-7/8" vertical table movement

Main Motor: 9 HP, 230/460v, 3PH Scoring Blade Motor: 1.25 HP, 230/460v,
3ph 126" Cut stroke capacity Main Blade Size: 8" - 15.75" Main Blade Bore: 30mm
Scoring Blade Size: 105-120mm (4.13" - 4.72") Scoring Blade Bore: 20mm
Main Table Size: 31" x 45" Sliding Table Size: 53" x 10"
TigerStop is shown in the picture.

Clamping Capacity, 55"- L x 96"- H x 24"- D, that's large enough for multiple boxes.
Pressure Elements (4) horizontal @ with (2) individual air pods, counter-weight balanced,
position them effortlessly and let go, the counter weight will keep them in place,
no need to individually secure them.
Air Pod stroke, 3-1/2" with pressure controls for each air pod pair.
Vertical Beam, moves easily on roller bearings with pneumatic carriage locks.
Operator Control Panel, mounted on vertical beam so it is always where it is needed,
single lever lock-or-unlock control & front/rear pressure selection.
Counter Support, by solid laminated panel opposite to pressure bars.

16" diameter, 1/2 HP,
1PH 115/230 motor, 1725 RPM